Introduction to svnserve
Following on from the Introduction to subversion article, we'll now look at svnserve (subversion's built in server).
Svnserve allows you to access your project from remote machines. Concentrating on configuration and basic setup, this article introduces this often overlooked program.
To check out 'project1' from a remote repository is very easy - it is usual to have the repository in a slice or other server and to work on the project (in this case project1) from a local machine such as your main workstation at home or work.
We start the process by logging onto your repository Slice and starting svnserve. When issuing the svnserve command include the full path to your repository:
svnserve -d -r /home/demo/repository
Short and sweet. Now we have svnserve allowing remote access to our repository on the default port of 3690.
If you have an iptables setup or other firewall, don't forget to allow connections to port 3690. This can be achieved by opening the iptables test file:
sudo nano /etc/iptables.test.rules
and adding this line before any final LOG & REJECT rules:
# Allows svnserve connections from anywhere -A INPUT -p tcp --dport 3690 -j ACCEPT
Temporarily give yourself root access:
and activate the changes:
iptables-restore < /etc/iptables.test.rules
A quick check of the rules will show this extra line:
iptables -L ... ACCEPT tcp -- anywhere anywhere tcp dpt:svn
Once happy, save the changes and exit out of the root access:
iptables-save > /etc/iptables.up.rules ... exit
Let's test it by checking out project1 (remember the IP address is for the slice containing the subversion repository:
svn co svn://22.214.171.1240/project1
That was quick and easy to do.
We now have access to project1 which is great but try committing any changes and you will get an 'svn: Authorization failed' error.
Although good (we don't want everyone submitting changes to project1), we need read and write permissions to the repository.
svnserve has a very simple configuration file. Open it up (on the slice hosting the repository):
The first thing you will notice is that everything is commented out. Let's delete all of that and start a simple configuration of our own.
# svnserve configuration [general] password-db = /home/demo/repository/conf/passwd anon-access = read auth-access = write realm = Project1
I think the options are fairly self explanatory but do note that if you didn't want general access to the repository (i.e. it's not available to the public) you would change anon-access to:
anon-access = none
Next open the passwd file (again, on the remote repository slice):
Enter authorised users along with their passwords:
[users] project1admin = mypassword
Let's make a small change to the project on our local workstation and, now that the permissions have been set on the remote repository, commit them:
mkdir goodbye svn add goodbye ... svn commit -m "Added goodbye folder" --username project1admin
Enter the password we set earlier and this is the result:
svn commit -m "Added goodbye folder" --username project1admin Authentication realm: <svn://126.96.36.1990:3690> Project1 Password for 'project1admin': Adding trunk/goodbye Committed revision 4.
For more svnserve options, enter:
Notice you can configure which port svnserve uses:
svnserve -d -r --listen-port 2122 /home/demo/repository
Or to respond to a single IP address only (my workstation IP for example):
svnserve -d -r --listen-host 188.8.131.520 /home/demo/repository
Naturally that would only work if I had a static ip address.
To make svnserve start on a reboot add the following to your crontab:
crontab -e @reboot svnserve -d -r /home/demo/repository
I am sure you will have noted that the connection to the subversion repository doesn't seem very secure.
That's because it's not :)
We'll fix that in the next article by using the SSH protocol to connect to the repository.
© 2015 Rackspace US, Inc.
Except where otherwise noted, content on this site is licensed under a Creative Commons Attribution-NonCommercial-NoDerivs 3.0 Unported License
See license specifics and DISCLAIMER